Calculators
Sheet metal calculators
Calculate sheet weight, bend allowance, press brake tonnage and V-die opening. Plan cylinder and cone blanks and compare rolling capacity for material planning and equipment selection.
| Calculator | Inputs you have | Question to answer | Result and scope |
|---|---|---|---|
| Metal weight | Material option, thickness, rectangular width and length, quantity | How heavy is the blank or batch? | kg/m², kg per piece and batch, total lb and whole pieces per metric tonne. Fixed material densities; holes and cut-outs are not deducted. |
| Bend deduction | Bend rotation angle, inside radius, thickness, K factor and outside leg dimensions A/B | What flat length corresponds to this single bend? | Bend allowance, bend deduction and two-leg flat length; not a multi-bend CAD unfolding. |
| Press brake tonnage | Material preset or confirmed tensile strength, thickness, bend length and V opening | What force does this air bend require? | Estimated tonnes-force for one bend; not confirmation of machine suitability. |
| V-die opening | Material category, thickness and an existing or proposed V opening | Which opening and flange assumptions should be reviewed? | Suggested V opening, material/thickness radius estimate and minimum flange estimated from the entered V. |
| Rolled cylinder blank | Inside, outside or mid-wall diameter, plate thickness, formed angle and axial width | How long is the flat blank for this shell or circular arc? | Mid-wall diameter, developed length and adjusted rectangular blank; geometry only, without springback, trim, joint gap or machine capacity. |
| Cone flat pattern | Large diameter, small diameter and axial height | What flat pattern does this concentric cone or frustum need? | Slant height, outer and inner developed radii, sector angle and both arc lengths; geometric cut outline without seam and trim allowances. |
| Plate rolling capacity | Roll layout, top roll diameter, plate thickness, plate width and target inside diameter | Can this machine roll and pre-bend the shell? | Outside diameter, remaining flat end and a comparison of the entered dimensions with published rolling and pre-bending limits. |
| Robotic bending-cell cost and payback | Incremental installed investment, labour rates, accepted-part quantity, paid labour hours and other annual costs | How do manual and robotic annual costs compare for the same accepted output? | Annual and unit costs plus simple payback when investment and annual net benefit are positive; no output prediction or extra-output value. |
Use only the tools your question needs
If you already have the inputs for your question, open that tool directly: a known rectangular blank can go straight to weight, and a known V opening can go straight into the force calculation. Use the sequence below when you need to connect tooling, flat-length and weight assumptions; it is not a mandatory process for every part.
Keep the same assumptions when connecting results
Start with the drawing revision, material grade and condition, actual thickness and units. Screen the V opening against flange and radius requirements, then use that same opening in the force calculation. Use a justified radius and K assumption for the bend calculation before estimating rectangular blank weight. Recheck the connected results if a tool change affects the radius or flat length. In the V-die tool, changing the entered V updates the flange estimate; the displayed radius remains a material/thickness estimate, not proof of the radius produced by the new die.
Use estimates to prepare a review
Weight supports material-cost, freight and handling planning. Flat length supports blank-size and material-utilisation estimates. Force is one input to machine and tooling review; a matching nominal capacity alone does not establish suitability. V opening affects tooling and flange support. Keep the assumptions together: a light part can still require a high bending force, and a short flange can rule out the opening assumed in that calculation.
Keep a reviewable calculation pack
Save inputs, units, assumptions and outputs with the drawing revision and tooling IDs. Tonnage-tool teaching example: the mild-steel preset at 450 MPa, 2 mm thickness, a 1000 mm bend and a 16 mm V opening gives approximately 15.25 tonnes-force. Separate weight-tool teaching example: one 1000 × 2000 × 2 mm rectangular blank using the fixed carbon-steel density of 7.85 g/cm³ weighs 31.40 kg. These are assumptions for calculation, not one measured factory part. Keep trial measurements separate from theory; measurements entered in the leaf-page trial records are user-entered and unverified. A blank CSV is a collection template, and an exported record is not factory trial evidence.
What the calculators do not replace
These estimates support calculation and quotation review. They do not replace a material certificate, machine capacity plate, tooling catalogue or trial bend, and do not approve a machine, tool or bending program. Confirm the inputs and results with engineering before committing a price or delivery date.
Units and conventions
- Calculation dimensions use millimetres; the bend tool also accepts inches and material-specific gauge selections. The weight tool reports kilograms and total pounds.
- Force is reported in tonnes-force using the conversion convention 1 tonne-force = 9.80665 kN.
- The bend tool uses rotation angle α, not the included angle β between the legs: α + β = 180°. Its displayed geometric conversion is not an unloaded trial measurement.
- Legs A/B are outside dimensions to the theoretical sharp corner, not tangent lengths.
- The weight page has a US Standard Gauge reference table for sheet steel. Calculations still take millimetres; do not apply that steel gauge table to aluminium or stainless steel.
Related pages
Equipment and technical enquiries
Contact JS Ragos about the equipment or technical topics covered here.
Contact us