Engineering tools Sheet metal forming

Plate Rolling
Calculator

See how your plate wraps around the rolls. Compare the minimum rolling diameter and pre-bend flat ends for published 3-roll and 4-roll machine examples.

3-roll & 4-rollLive cross-sectionMetric & imperial
01 / INPUTS

Set up the job

Roll layout
mm
mm
mm Measure along the roll axis. Width affects machine capacity.
mm

Catalog example · 260 MPa steel

02 / LIVE DIAGRAM

Roll geometry

4-roll layout
Rolls Plate Flat end

Schematic. Roll positions and line thicknesses are adjusted for clarity.

03 / RESULTS

Geometry & capacity reference

Target outside diameter—Inside diameter + 2 × thickness
Listed minimum rolling Ø—Selected catalog example
Remaining flat per end—After pre-bending, where applicable

Equipment and technical enquiries

Contact JS Ragos about the equipment or technical topics covered here.

Contact us

How to calculate minimum plate rolling diameter

Enter the top roll diameter, plate thickness, plate width and target inside diameter. Plate width runs along the roll axis. Choose My dimensions to explore the geometry, or load a three-roll or four-roll catalog example to compare published limits for 260 MPa steel.

Geometric diameter

For a circular shell of uniform thickness, outside diameter = inside diameter + 2 × plate thickness. A plate that wraps around the top roll also needs enough inside clearance. Actual rolling capacity depends on roll layout and travel, available force and torque, and the plate width, thickness, yield strength and springback.

Pre-bending and the remaining flat end

The remaining flat end is the portion at each end that does not reach the intended curvature. If a manufacturer specifies a residual flat length limit as a multiple of plate thickness, multiply that coefficient by the thickness defined in the specification. Check whether it refers to the job thickness or the rated maximum thickness. Roll count alone does not establish a coefficient.

Three-roll machine reference

For arc-adjusted lower-roll machines, JB/T 10924–2010 gives a minimum cylinder diameter at rated maximum width and thickness and 245 MPa yield strength. Multiply the top roll diameter by 2.5 for rated maximum thicknesses up to 60 mm, or by 3 above 60 mm. Other three-roll layouts have their own capacity limits.

Four-roll worked example

Faccin’s published 4HEL 202 row lists a 2000 mm plate width and a 210 mm top roll. At 5 × 210 = 1050 mm, the catalogue lists 10 mm rolling thickness and 8 mm pre-bending thickness. At 1.4 × 210 = 294 mm, it lists 6 mm pre-bending thickness. The row gives no rolling capacity at 294 mm. Each figure applies to its published model and operation.

Plate rolling calculator FAQ

How do I calculate the minimum rolling diameter?

Use the machine's capacity chart to find the smallest rated diameter for your plate width, thickness and material grade. Confirm whether the chart gives an inside or outside diameter and check the pre-bending rating if the plate ends must reach the same curvature. For a round shell of uniform thickness, inside diameter equals outside diameter minus twice the plate thickness. See the calculation method.

What is the difference between a 3-roll and a 4-roll plate rolling machine?

A typical four-roll machine clamps the plate between a top and bottom roll and uses side rolls to pre-bend the ends while the plate stays clamped. Three-roll machines vary by layout. A variable-geometry three-roll model can move its lower rolls independently to handle heavy plate and shorten the flat ends. Compare the pre-bending and handling capabilities of the specific models. DAVI's roll configuration guide

What is the difference between rolling capacity and pre-bending capacity?

Rolling capacity tells you how thick a plate the machine can curve through the body of the cylinder. Pre-bending capacity tells you how thick a plate it can curve at the ends, and is often lower. Compare both ratings for the same material, width and target diameter. See the Faccin worked example.

How can I reduce flat ends when rolling plate?

Pre-bend both ends using the sequence specified for your machine. Check the remaining flat length at each end against the seam tolerance. If the rolls cannot meet that tolerance, a separate pre-bending operation with suitable press tooling can help. The calculator shows the catalog estimate per end. HARSLE's plate rolling FAQ

Technical references