Read piece weight, batch weight and pieces per tonne
Weight per square metre (kg/m²) depends only on density and thickness. Width and length determine the piece weight; quantity changes only the batch totals in kg and lb. Pieces per metric tonne is floor(1000 ÷ piece weight in kg), independent of batch quantity. A piece heavier than 1000 kg gives 0; a piece weighing exactly 1000 kg gives 1.
Check rectangular dimensions and fixed material densities
Fixed density assumptions (g/cm³):
- Thickness, width and length are entered in millimetres; the blank is treated as a rectangle with square corners.
- The densities used are carbon steel 7.85, stainless 304 7.93, stainless 316 7.98, aluminium 2.70, copper 8.96, brass 8.50 and galvanized steel 7.85 g/cm3.
- The galvanized-steel figure uses the steel core density and ignores the zinc layer.
- Quantity must be a whole number. A layout with holes, cut-outs or a non-rectangular outline needs a separate area calculation.
- Results are not adjusted for thickness tolerance, edge condition or surface treatment.
These are fixed density assumptions, not measurements of your batch. There is no custom-density field. If the certificate gives a different density, calculate separately with the formula below.
Dimension examples and input limits
Software input limits: thickness greater than 0 and at most 100 mm; width and length greater than 0 and at most 20000 mm; quantity an integer from 1 to 1000000. These limits describe accepted inputs, not machine capacity.
Dimension examples retained for reference: thickness 0.5–20 mm, including 1–6 mm; widths 1000, 1250, 1500 and 2000 mm; lengths 2000, 2500, 3000 and 6000 mm. These are examples, not recommended sizes or evidence of process capability.
Calculate mass from density and blank dimensions
Mass in kilograms equals density in grams per cubic centimetre multiplied by thickness, width and length in millimetres, then divided by 1000000. The divisor converts cubic millimetres and grams into kilograms: one cubic centimetre is 1000 cubic millimetres, and one kilogram is 1000 grams. As a check, one square metre of 1 mm carbon steel at 7.85 g/cm3 weighs 7.85 kg.
Weight per square metre is simpler: density multiplied by thickness. That is why 1 mm carbon steel reads 7.85 kg/m2 and 2 mm reads 15.70 kg/m2. Pieces per tonne is the whole-number result of 1000 kg divided by the weight of one piece.
If you need the flat dimensions from a bent part, first use the bend deduction calculator.
Check the dimensions and one result
Enter the rectangular flat blank dimensions, not the folded part envelope. Teaching assumption, not a weighing record: carbon steel at 7.85 g/cm3, 2 mm × 1000 mm × 2000 mm gives 7.85 × 2 × 1000 × 2000 ÷ 1000000 = 31.40 kg per piece and 15.70 kg/m². Ten identical blanks give 314.00 kg; floor(1000 ÷ 31.40) = 31 whole pieces per tonne. That piece count is a mass conversion and says nothing about nesting yield.
Gauge reference boundary
The table on this page is labelled US Standard Gauge for sheet steel. Aluminium and stainless steel use different gauge systems, so this table must not be used to convert their gauge numbers. Enter aluminium and stainless steel thickness in millimetres. If a drawing gives only a gauge number for one of those materials, ask for the millimetre thickness before using the calculator.
The gauge reference uses the statutory US Standard Gauge thickness series, not the commercial Manufacturers Standard Gauge (MSG) series. For example, statutory 16 gauge is 0.0625 in = 1.5875 mm. The mass result still uses the selected density assumption; it does not reproduce the statutory mass column.
Reconcile the estimate with purchased and shipped mass
Confirm the grade and thickness tolerance from the certificate and measure representative thickness with an appropriate calibrated instrument. Record any cut-outs, coating, packaging, pallet and scrap separately; do not hide them in the rectangular blank result. For an actual batch, weigh it on a suitable verified scale and record gross mass and tare to obtain net mass. Compare that net mass with the calculation on the same quantity and scope. The local trial-bend record is not a weight ticket, a lifting plan or proof of load capacity.
The CSV export combines the theoretical inputs and piece/batch mass with user-entered, unverified trial-bend fields. Changing calculator inputs clears the previous measurement draft. Edit the input fields to recalculate; there is no calculator reset button.
Using the result in a quotation
Use the piece weight for material cost and the batch weight for freight, pallet loading and lifting. Add scrap and skeleton loss from the nesting layout rather than applying a single percentage to every job. Pieces per tonne helps compare a quoted price per tonne with a price per piece. When a batch is close to a crane or pallet limit, confirm the limit with the workshop before the weight is written into the quotation.
Blank mass does not give the bending force. For that separate calculation use the press brake tonnage calculator.
Confirm material and blank area before quoting
The result is an estimate for quotation preparation. Confirm the material grade, density, thickness tolerance and blank area with engineering before quoting. Do not use the calculator output as a shipping declaration or as a substitute for a certified weight ticket.