What should you check before buying a press brake?
Choose a press brake by checking the parts it must make, the tooling needed to make them, and the production routine around the bend. Start with representative drawings and the material and thickness range.
Check force and bend length together with die opening and part clearance, then compare the drive, backgauge functions and changeover requirements. Ask each supplier to quote the same tooling, service scope and acceptance work before comparing price.
Step 1: check part dimensions, materials and handling needs
- Maximum bend length across the part, including any bend that runs the full sheet.
- Thickness range, from the thinnest to the thickest sheet in the work mix.
- Material grades, because tensile strength changes the force needed at the same thickness.
- Minimum flange height on the drawing, which limits the tooling that can reach the bend.
- Part weight and how it will be lifted, supported and turned on the table.
- Distance between the side frames, which is narrower than the bending length and decides whether a long blank can sit between the frames at all.
- Throat depth for return flanges and box-shaped parts, because a part can run out of reach before it runs out of force.
- Opening height and stroke against the tooling and the part profile, especially when a deep section has to be loaded.
Select representative difficult parts as well as the most frequent work. The longest or return flange affects clearance; the shortest flange limits support over the die opening. Keep both dimensions in the selection record.
Step 2: match tonnage and bend length to the V-die opening
Tonnage follows from material, thickness, V-die opening and bend length together, not from thickness alone. The V opening also sets the inner radius and the minimum flange, so a tooling choice made only for force can make a short flange impossible to form.
Required force rises with sheet thickness, with the length of the bend and with the tensile strength of the material. The rated tonnage of a machine is a ceiling, and the bending length is a second ceiling that acts independently.
A machine can have enough force and a table too short for the part, or a long table and too little force for the material. Both values have to be checked against the worst part in the family, not against an average part.
The tonnage and V-die calculators on this site work through both relations; use them with the drawing values, then confirm the tooling against the machine and the part.
- Calculate the force for the actual material, thickness, bend length and die opening; do not scale from a neighbouring thickness.
- Keep margin above the calculated force so that a higher-strength delivery or a smaller die opening does not push the machine to its limit.
Step 3: check tool clearance, clamping and changeover needs
The tooling interface decides how fast a die and a punch can be changed and how repeatable the seating is. Clamping systems range from manual clamps to quick-release and hydraulic clamps, and the choice matters most where changeovers are frequent.
Segmented tooling lets a short punch or die be assembled for a part that only needs part of the bed, while a full-length tool is simpler when the same bend runs for a long time. The die opening, the punch tip and the punch height still have to match the radius and the flange depth; the interface only changes the time it takes to get there.
- Match the die opening to the thickness and the required inner radius before choosing a clamping system.
- Check the punch height and the tip form against the flange depth and any return flange on the part.
- Confirm with the supplier that the tool and clamping-chain load ratings and the machine force limit are matched for the actual setup and engaged length, according to the supplier instructions.
- Plan the storage and the handling of heavy tooling, because a fast clamp does not help if the die cannot be moved safely.
Step 4: compare machine motion, drive and tandem options separately
The table compares motion, drive and machine arrangement. These dimensions can be combined; confirm the available combination and supplied configuration in the quotation.
| Dimension | Configuration | What changes | What to verify |
|---|---|---|---|
| Motion | Up-acting | The lower table carries the die upward against a fixed upper beam | Check bend-line visibility, loading and support for the actual small or medium part and work mix. |
| Drive | Electro-hydraulic | A pump and valve block drive hydraulic cylinders that move the ram | Compare the required force, control functions and available hydraulic maintenance support. |
| Drive | All-electric | Servo motors drive the ram through a mechanical transmission rather than a hydraulic bending circuit | Confirm the part envelope, programmed cycle, electrical supply and service requirements. |
| Drive | Hybrid | A servo-driven pump supplies a hydraulic circuit | Request the actual operating and standby conditions; the drive label alone does not establish energy per part. |
| Arrangement | Tandem | Two press brakes are linked and synchronised for a long bend | Verify usable combined length, synchronisation, tooling alignment and handling at the joint. |
For brackets and enclosures with suitable force, bend length and clearance requirements, assess the fixed upper beam and rising lower table of the MG up-acting press brake. Check part weight, support and tooling before choosing a model. A linked pair addresses length but also needs coordinated loading and synchronisation.
Compare candidates on the same parts and feasible tool set before comparing their documented production cycle. Include loading, turning, gauging, tool changes and accepted output, rather than treating catalogue travel speed as finished-part throughput. Connected power is an installation figure; it does not establish energy per accepted part.
Step 5: match backgauge positioning to each bend in the part
The backgauge positions the sheet against a stop. Depth, height and lateral finger movement serve different contact and clearance needs. Work through each bend in the drawing: identify the face that can be gauged, the finger positions and any retreat needed to clear a formed flange.
Ask the supplier to show how the proposed gauge and control follow that sequence, including any manual repositioning. One repeated bend may need fewer functions than a changing enclosure job. Confirm what each axis actually moves and how it is programmed; axis names and counts alone do not demonstrate a usable sequence.
Step 6: distinguish machine deflection, shimming and springback
Under load, the ram, bed and tooling can deflect along the working length. Crowning applies a designed compensating curve or force, for example through a wedge table or hydraulic system, to address that deflection. Local shimming changes the tooling setup at selected positions. The methods have different setup and repeatability implications; they are not interchangeable labels.
First compare measured angles at both ends and the middle. Variation along the bend calls for a different investigation from a similar offset at every position. Neither pattern alone proves a cause. Crowning is not a universal correction for springback, tool wear, material variation or a wrong bend allowance.
- Choose crowning when the part is long and the angle has to stay consistent along the bend; short bends may not show the effect clearly.
- Confirm whether the compensation is manual, motorised or under numerical control, because that decides setup time.
- Check the compensation range against the material and thickness the shop actually runs, not against the lightest job.
- Remember that crowning corrects machine deflection, not tooling wear, material variation or a wrong bend allowance.
- Without compensation, a long bend can be over-bent at the ends and under-bent in the middle, or the reverse, depending on the setup.
- Mistaking shimming for crowning can leave a correction that works at one point and distorts the rest of the bend.
- Over-compensating produces its own angle error, so more crowning is not automatically better.
- A crowning setting proven on one material and thickness is not automatically correct for another.
Step 7: confirm installation, safety and supplier service scope
- Confirm what each controlled axis moves and how the control handles the representative bend sequence.
- Agree the safety-device scope and working-cycle interfaces for review by the responsible safety and compliance parties.
- State the available electrical supply, connected-load limits and site conditions.
- Check access, lifting and placement arrangements, floor-space needs and the proposed layout.
- Identify how the part and heavy tooling will be supported, stored and handled.
- List installation, commissioning and training scope, language, responsibilities, costs and exclusions.
- Ask the supplier to identify unresolved site or applicable safety requirements before fixing the configuration.
Step 8: agree trial parts and acceptance checks before ordering
Use representative difficult parts for quotation and agree the trial setup, critical dimensions, surface requirements, measurement positions and acceptance criteria before the run. Include those records in the quoted scope and order. Check the complete formed part, not only one angle; record unresolved feasibility items instead of treating a demonstration or a calculated tonnage as proof.
How to check angle consistency along a long bend
- Use a representative bend length to assess variation along the part; a short sample does not establish full-length behaviour.
- Measure at agreed positions, including both ends and the middle, under the same measurement convention.
- Have the responsible operator review any adjustment against the actual machine and tool instructions; repeat the agreed measurements after a change.
- Record material, actual thickness, tool IDs, engaged length, compensation settings and results so a later batch can be compared.
The press brake tonnage calculator estimates total force F. For an average line load, divide F in kN by the actual engaged tool length L in metres: F/L in kN/m. Check the supplier-rated limits for the punch, die, clamping and machine, including local and concentrated loading.
An average below one tool rating is not a loading approval. The bending process page explains springback, a separate issue from deflection along the bend.
What tonnage and price alone leave out of your selection
- Choosing on maximum tonnage alone, without the flange and tooling the part needs.
- Ignoring minimum flange height until the tooling cannot reach the bend.
- Checking the angle at one end of a long part and not along its length.
- Leaving tooling change time out of the cycle when the batch changes often.
- Comparing quotations without the same tooling list and acceptance items on both.
- Treating shimming and crowning as interchangeable, or applying one crowning setting to another material and thickness.
Press brake product range
The MG up-acting and NG electric lines, with the model tables and selection notes.Press brake tonnage calculator
Force for the material, thickness, bend length and die opening.V-die opening calculator
Match the die opening to the thickness and the required inner radius.Press brake bending process
Springback, minimum bend radius and bend deduction explained at the bench level.
What drawings and requirements should every supplier quote against?
| RFQ field | Compare on the same basis |
|---|---|
| Part envelope | Drawing revision, critical dimensions, material grade and condition, actual thickness range, grain direction, shortest and return flanges. |
| Force and tooling basis | Bend length, proposed V opening, punch/die interface, engaged tool length, rated loading and assumptions still to confirm. |
| Work mix and handling | Batch size, annual-demand assumption, changeovers, part weight, supports, loading and turning. |
| Machine and control scope | Motion and drive configuration, backgauge functions, control options, named tooling and items included or optional. |
| Site and service scope | Electrical supply, layout and lifting, installation, commissioning, training language, responsibilities, costs and exclusions; state whether freight and transport charges are included or itemised separately. |
| Commercial comparison | Ask each supplier to state quote validity, currency, payment milestones, delivery-stage definitions, trade term and named place, and warranty start, duration, coverage and exclusions. |
| Trial and acceptance evidence | Agreed representative parts, setup and measurement method, acceptance criteria, required records and unresolved feasibility items. |
Ask each supplier to mark every item included, optional, excluded or still unverified. Compare the complete delivered scope and the same trial parts before comparing price. Do not turn a calculated tonnage into a machine or tooling load approval.