Tonnage is the estimated force for one air bend. It depends on tensile strength Rm (MPa), sheet thickness t (mm), actual bend length L (mm) and actual V-die opening V (mm). The calculator outputs metric tonnes-force (tf); t in an input means thickness, not tonnes-force. With material, thickness and V unchanged, doubling L doubles total force.

Enter these four inputs in the press brake tonnage calculator.

What tonnage measures at the machine

InputUnitWhat to record
RmMPaActual tensile strength, not yield strength; a material preset is not a measurement
tmmSheet thickness
LmmLength taking part in this bend, not the whole blank width
VmmActual die opening

In air bending, the punch presses the sheet into a V-die and the sheet touches the die at two edges. The force has to bend the material across the opening and hold it at the target angle. The required tonnage is that force, expressed in tonnes-force for one bend. It is not the machine rating and it is not a property of the thickness alone.

The machine rating is a limit. The calculated tonnage is a demand. A necessary capacity check is that estimated demand remains within the applicable limits for the actual material and tooling; this alone does not establish a safe setup. Two parts with the same thickness can sit on opposite sides of that line when one bend is twice as long as the other.

Press brake tonnage is not a single number: it depends on thickness, bend length, V opening and material tensile strength. A tonnage value copied from a chart without all four inputs describes a different bend. The number a quotation needs is the force for this material, this thickness, this bend length and the die that will actually be fitted.

Reading a tonnage chart without getting burned

A tonnage chart is a set of worked examples, not a universal table. A row is valid only for the material, thickness, V opening and bend length it states. Charts commonly use a one-metre reference length, which is a typical convention rather than a rule; always read the note that says what the row assumes.

Read the chart in this order: process, material and tensile strength, thickness and V, reference length, force unit, then actual bend length. The English 3-page PDF is a theoretical air-bending reference for mild steel at 450 MPa and 1000 mm bend length, covering thicknesses 1–6 mm and V/t = 6/8/10/12; it does not cover 8 or 10 mm sheet. The 2 mm, V = 16 mm row prints 15.3 metric tonnes-force, 149.6 kN and 16.82 US short tons-force. Each column is converted separately from the unrounded theoretical force and rounded to its own precision. Do not convert one rounded column back into another and expect exact equality. These are force units, not interchangeable numbers or machine ratings.

  • Scale the published value in proportion to the real bend length before comparing it with the machine.
  • Start from tensile strength when the material differs from the chart material, rather than applying a single correction factor.
  • Check the rated force of the punch and die as well as the rated force of the machine.
  • Review material variation against the machine instructions. Bottoming or coining requires its own approved load and tooling assessment; do not cover it by an unspecified air-bending margin.
  • For a new part or material lot, first establish that machine, tooling and local load limits are satisfied, then use an approved trial procedure to check the part. A trial is not a way to discover whether an unknown or marginal load is safe.

Thickness enters as a square

For air bending, the force rises with the square of thickness. If the thickness is multiplied by a factor, the force is multiplied by that factor squared, with bend length, V opening and material held constant. A part moved from t to 1.5t therefore needs about 2.25 times the force, not 1.5 times.

That square relationship is why a small drawing change can invalidate a proven program. A thickness increase that looks modest on the drawing can push the demand past the machine limit or past the load limit of the punch and die. The relative increase follows the thickness ratio: for the same absolute thickness change, the relative increase is larger on thinner sheet.

The square relationship holds at fixed V, not at fixed V/t. If V changes with t to keep V/t constant, include that V change as well. Before comparing two calculator runs, record and check V in both; if V also changed, include V1/V2 in the relative formula rather than comparing thickness squared alone.

Bend length is linear

Force rises linearly with bend length. Double the length of the bend line and the force doubles, provided the material, thickness and V opening stay the same. This is why tonnage charts usually publish a reference length and why a shop scales the value in proportion to the real bend. A chart row for a short bend cannot be applied unchanged to a full-width panel.

Bend length also defines the engaged tooling length. Compare total force F with the approved machine capacity, and line load F/L with the punch and die ratings in the same units, using actual engaged length L in metres. Local or concentrated-load restrictions still apply; a low total force alone does not establish that a short tool segment can carry it.

For the same material, thickness, V and process, using the same force unit: F_actual = F_chart × L_actual/L_reference. Keep both lengths in the same unit. The PDF row is total force for 1 m of bending; dividing by 1 m gives the same numerical value but a different quantity: average line load. With F in kN and L in m, F/L is kN/m. Dividing by a length in mm does not give kN/m. An average cannot replace local-load limits.

The V opening moves force and geometry together

A larger V-die opening reduces the tonnage required for the same thickness and bend length. The same opening also increases the inside radius and the minimum flange length. The die is therefore a geometry decision as well as a force decision. Opening the die to lower the tonnage changes the part: the radius grows and a short flange may no longer be formable.

VariableEffect on forceEffect on geometry
Thickness increasesRises with the square of thicknessSame die produces a heavier section
Bend length increasesRises in direct proportionLoad spreads along the full bend line
V opening increasesFallsLarger inside radius and longer minimum flange
Tensile strength increasesRises in proportionSpringback may change; verify the actual material and process

This table gives qualitative force and geometry trends under the stated model conditions. Springback is not an output of the tonnage model; check actual material and process separately for angle verification.

For inside-radius and short-flange constraints, use the V-die opening calculator.

Tensile strength is the material multiplier

Force rises with the tensile strength of the sheet. A stainless steel and a mild steel at the same thickness and the same V opening do not need the same tonnage, because the stress required to bend them is different. Using a blanket material factor hides that difference. The safer input is the tensile strength stated for the actual heat or grade, not a label such as stainless or aluminium.

In the same model with all other inputs unchanged, force scales with Rm. Use the upper end of a certificate range for a preliminary force check. A stronger coil can demand more force than another of the same grade; material variation also needs a separate angle check.

Compare a changed job with its documented baseline

Here 1 is the documented baseline and 2 is the changed job. Pair corresponding inputs in the same units, within the same air-bending model and coefficient.

Within the same approximate air-bending model and coefficient, F2/F1 = (Rm2/Rm1) × (L2/L1) × (t2/t1)² × (V1/V2). This ratio is a model sensitivity check, not a new force law or machine test. If only thickness increases by 10%, the estimate increases by 1.1² = 1.21, or 21%. Changing process, contact conditions or special tooling can invalidate the comparison.

What the calculation does not cover

An air-bending tonnage calculation does not describe bottoming or coining, where the punch presses the sheet against the die face and the force can rise well above the air-bending value. It does not describe a bend that needs a special tool or a radius that the standard V opening cannot produce. It also does not replace the machine builder load chart for the tooling being used. Treat the number as the air-bending demand for one bend, and check the exceptions before the job is released.

Use the tonnage estimate to assess force demand. Before releasing the setup, verify actual material inputs, machine capacity, tooling and local-load limits against the equipment instructions; verify angle and part accuracy separately.

A practical check before quoting

Before accepting the quoteRequired evidence
Model identityAir bending, unit convention and original material/length/thickness/V inputs
Machine capacityBuilder limits for total force, location and distribution of load
Tooling capacitySame-unit force per engaged length; actual punch, die, holder and local-load limits
Part resultSpecified unloaded angle/radius, flange geometry and first-part check

Use the calculator for an absolute force estimate and the tooling pages for load-per-length checks. Check clearance and finished-part accuracy in the approved setup and trial procedure.

  • Read the material grade and its tensile strength from the drawing or the mill certificate.
  • Read the thickness and the bend length, and count how many bends share the same tooling.
  • Choose the V opening from the required inside radius and the shortest flange, not from tonnage alone.
  • Calculate the force per bend, then compare the highest value with the machine and tooling limits.
  • Record the inputs with the quotation so the next order can be checked against the same assumptions.

Calculate sequential bends individually rather than adding their forces. To decide on a machine, continue with the press brake selection guide and check the force–length envelope, tooling chain and part clearance.

Use this force estimate to discuss the workpiece and tooling requirements for Press brake range. Confirm the supplier's rated force units and the applicable capacity limits before comparing machines.

Summary

Press brake tonnage is a demand calculated from thickness, bend length, V opening and tensile strength, not a fixed property of a gauge. Thickness enters squared, bend length enters linearly, a larger V opening lowers force but enlarges the radius and minimum flange, and tensile strength scales the result. Use the tonnage calculator for the part in front of you, and keep the tonnage chart as a cross-check on the same assumptions.