Bend allowance (BA) is the neutral-axis arc added to the straight tangent lengths. Bend deduction (BD) is subtracted from the sum of the two outside dimensions, each measured to the virtual sharp corner. With the same angle, inside radius, thickness and K factor, both routes give the same flat length. K locates the neutral axis; it is not another length to add or subtract.

One bend, two descriptions

A bent part has an inside face, an outside face and a layer between them that neither stretches nor compresses in the simple model. That layer is the neutral axis. Bend allowance measures the length of the arc along it. Bend deduction starts from the outside corner dimensions that a drawing usually shows and removes the material that the bend consumes. The two quantities are linked by geometry, so a correct bend allowance and a correct bend deduction must agree on the same flat length.

Choose by the dimension basis and the unfolding rule, rather than by job title. Use BA with straight tangent lengths and BD with outside dimensions each measured to the virtual sharp corner. The two routes can cross-check one another when their inputs agree.

Bend allowance: the arc at the neutral axis

Bend allowance is the developed length of the bend itself. It is calculated from the bend angle, the inside radius and the position of the neutral axis. Written as a relationship, the allowance is the bend angle in radians multiplied by the radius of the neutral axis, where that radius is the inside radius plus the K factor times the thickness.

Because the allowance is an arc, it grows with the bend angle and with the radius. A 90 degree bend has a longer arc than a 45 degree bend at the same radius. A large radius has a longer arc than a tight radius at the same angle. The allowance does not depend on the length of the legs, which is why it can be tabulated once the material, thickness, radius and K factor are fixed.

Bend deduction: the outside view

Bend deduction works from the outside dimensions. Each outside leg, measured to the theoretical sharp corner, includes a setback that the bend will consume. The deduction is the sum of the two outside setbacks minus the arc that replaces them. Subtracting the deduction from the sum of the outside legs gives the flat length directly, without unfolding the arc by hand.

QuantityMeasured fromUsed toMain inputs
Bend allowanceNeutral-axis arcAdd the neutral-axis arc to straight tangent lengthsAngle, inside radius, K factor, thickness
Bend deductionOutside dimensions each to the virtual sharp cornerSubtract BD from the sum of outside dimensionsAngle, inside radius, K factor, thickness
Outside setbackOutside corner to tangent pointBuild the deduction from outside geometryAngle, inside radius, thickness
K factorNeutral-axis position in the thicknessLocate the neutral axis for either methodRadius-to-thickness ratio, material

The table is a map, not a set of independent variables. Once the angle, inside radius, thickness and K factor are fixed, the allowance and the deduction are two views of the same bend. Changing the K factor moves both.

The flat length relationship

First classify the dimensions. Use α for bend rotation and β for the unloaded included angle: α + β = 180°. A 120° included angle therefore means α = 60°, not 120°. For a simple straight bend with constant thickness t and inside radius R, the geometric model is BA = (π α / 180)(R + Kt), SB = (R + t)tan(α/2), BD = 2SB − BA and flat length L = A + B − BD. A and B are outside dimensions to the virtual sharp corner. These relationships are not hem, coining or variable-thickness models.

Equivalently: L = (A − SB) + (B − SB) + BA = A + B − BD.

For a part with two outside legs A and B, the flat length is A + B minus the bend deduction. That single line is the reason bend deduction is popular at the press brake: the drawing dimensions can be used directly, and the correction is one subtraction. The same flat length can be reached with bend allowance by replacing each outside leg with its flat length up to the bend tangent and then adding the allowance.

If A and B are outside dimensions, L is not A + B. Convert them to straight tangent lengths before adding BA. If the drawing already gives the complete developed length L, apply neither BA nor BD again. Label outside dimensions, straight tangent lengths and complete developed length separately.

For bending methods, tooling and springback background, see the bending process page

The K factor is an assumption until it is calibrated

The K factor is the neutral-axis position ratio: the distance of the neutral axis from the inside face divided by the thickness. It is typically between 0.3 and 0.5 depending on the radius-to-thickness ratio and the material, and it must be calibrated for the actual process. A value taken from a handbook is a starting assumption, not a property of the sheet.

The K factor moves with the radius-to-thickness ratio because a tight bend and a generous bend do not distribute strain through the thickness in the same way. It also moves with the material: a high-strength sheet and a soft sheet at the same radius can need different values. The only reliable calibration is a trial bend on the production material and tooling, measured against the predicted flat length.

  • Cut a test blank with a known flat length and bend it with the production tooling.
  • Measure the resulting outside dimensions and compare them with the prediction.
  • Adjust the K factor until the predicted flat length matches the measured part.
  • Record the value with the material, thickness, radius and tooling it was calibrated on.
  • Recalibrate when the material source, grade or tooling changes.

The 0.3–0.5 interval is a common reference range, not a measured range for every material and tool or a hard calibration limit. A fitted K applies only to the recorded material, thickness, radius and process conditions.

Full measurement and correction procedure: trial-bend guide

The next section’s diagnostic table gives the checks for dimension basis, unloaded angle and inside R; complete them before adjusting K.

Resolve a flat-length mismatch before changing K

Check in orderEvidence to retainDecision
Drawing dimensionsA/B virtual-corner or tangent dimensions; drawing revisionConvert only once; do not subtract BD from tangent lengths
Angle and radiusUnloaded β, measurement positions, measured inside RResolve a wrong angle or radius before fitting K
Blank and processKnown original L, actual t, material lot, tool IDs and V openingCompare the same physical process
CalibrationBD observed = A + B − L; BA observed = 2SB − BD observedK estimated = (BA observed / (π α/180) − R)/t; retain raw readings

When CAD and the shop disagree, check the bend angle, dimension basis and blank condition before fitting K. An implausible fitted K is a reason to revisit those inputs. [A1]

Use the same single-bend specimen without subsequent trimming for the inverse calculation.

Consistency beats sophistication

Record the dimension basis, angle definition, unfolding rule, K assumption, radius and drawing/table revision across the drawing, nesting, brake program and inspection sheet. BA and BD may cross-check one another; update linked records together when an assumption changes.

Keep the calibration conditions with the value. Agreement on one specimen does not establish production repeatability.

Common mistakes

  • Adding bend allowance to outside leg dimensions instead of converting the legs first.
  • Applying BA or BD again to a complete developed length, or subtracting BD from straight tangent lengths.
  • Using a mild-steel K factor for stainless steel, aluminium or high-strength steel.
  • Changing the V-die opening without updating the inside radius and the deduction.
  • Treating a handbook K factor as calibrated when no trial bend has been measured.

Summary

BA adds the neutral-axis arc to straight tangent lengths; BD is subtracted from the sum of outside dimensions each measured to the virtual sharp corner. With consistent geometry and K they give the same L. K remains a conditional assumption until calibrated for the recorded process.