What laser cutting is
Laser cutting uses a focused beam to melt or burn sheet along a programmed path. It produces profiles, holes and contours from flat sheet and is usually chosen when the outline is too complex for shearing or when a hole pattern has to be cut in one operation.
Check edge quality, dimensions and finishing needs
| Item | Common route or requirement | Conditions to confirm |
|---|---|---|
| Cut quality | Where specified, agree edge characteristics and applicable quality ranges | ISO 9013 |
| Carbon steel assist gas | Oxygen — Common example, not the only gas route | Confirm the carbon-steel grade and thickness, equipment and validated route; check permitted edge oxidation and downstream finishing requirements. |
| Stainless steel assist gas | Nitrogen — Common example, not the only gas route | Confirm the stainless-steel grade and thickness, equipment and validated route; check required edge oxidation condition and downstream finishing requirements. |
| Aluminium assist gas | Nitrogen — Common example, not the only gas route | Confirm the aluminium grade and thickness, equipment and validated route; check required edge oxidation condition and downstream finishing requirements. |
| Thickness capability | Material/model specific | Supplier process envelope required |
Check the machine’s usable capacity for the specified material and thickness, then inspect representative straight edges, corners and holes against the drawing.
Verify the actual material, thickness, equipment, edge oxidation requirement and downstream operations; material identity alone does not select the gas.
Record the actual grade, coating and thickness with the machine and part geometry. Identify straight edges, corners and holes separately in the trial record; a result on one contour does not establish capability for every feature.
Oxygen-assisted flame cutting uses the reaction with oxygen as part of the process; inert-gas fusion cutting uses gas to expel molten material. Select the route for edge oxidation, thickness, machine configuration and downstream finishing needs. TRUMPF explains the fusion-cutting mechanism. [A1]
Oxygen cutting of carbon steel
Oxygen-assisted cutting is a common carbon-steel route, not the only option. Oxygen supports the cutting reaction. Check edge oxidation, dross and burr against the drawing and downstream finishing requirements. Verify the actual route for the material, thickness and equipment rather than transferring a setting from a material name.
Nitrogen cutting of stainless steel and aluminium
Nitrogen-assisted fusion cutting is a common route for stainless steel and aluminium, not the only option. The inert-gas route limits oxidation during cutting; it does not guarantee a clean or burr-free edge. Confirm the edge requirement, actual material, thickness, equipment and downstream operations. Nitrogen is not reserved exclusively for these materials. [A1]
Recognize edge defects and record observations
- Dross: resolidified material attached to the underside of the cut.
- Burr: a rough edge that needs deburring before the part can be handled or coated.
- Heat-affected zone: a band of material whose properties differ from the parent sheet.
| Observation | Evidence to retain | Judgement boundary |
|---|---|---|
| Dross or burr | Top and bottom edge photos, location and required removal or finishing | Compare with the agreed edge and finishing requirement; appearance alone does not prove conformity. |
| Roughness or striations; apparent taper | Identify the feature and location; agree the measurement method, locations and reference before comparing results | Photos and a simple top-to-bottom width difference do not establish an ISO quality range or a standard taper measurement. |
| Possible heat effects | Retain the location and original observations; confirm any required feature and test method against the drawing/application | A heat-affected zone is not automatically unacceptable. Visible colour does not establish its extent or mechanical properties. |
If the method or acceptance criterion is not agreed, retain the original observation and its location, and identify the method or criterion still to be confirmed. Do not declare a quality range or conformity from photos or measurements that cannot be compared.
First-cut acceptance worksheet
| Hold constant | Observe and record | Decision |
|---|---|---|
| Material grade, thickness and coating; drawing revision | Trial ID, gas/process, approved program and nozzle setup | Use the actual qualified process; do not copy a recipe by material name alone |
| Contour and edge requirement | Top/bottom edge photos, dross location, dimensional checks and downstream finishing | Separate appearance, dimension and finishing requirements |
| One authorised variable per comparison | Original setting, revised setting and same-location result | Retain failed samples; a cleaner edge alone is not proof of dimensional conformity |
The approved program and setup are traceability records, not a replacement for the drawing or agreed acceptance criteria. This worksheet does not instruct changes to machine settings.
When to choose laser cutting
- Choose it for complex outlines, hole patterns and contours that a shear cannot produce.
- Choose it when a flat part needs one setup for many features.
- For straight blanks, compare shearing with laser cutting against the geometry and required edge. Compare actual quotations using batch size, programming and downstream finishing needs; neither route is universally cheaper.
- Do not choose it when the heat-affected zone is unacceptable for the material or the application.
Common mistakes
- Citing ISO 9013 without agreeing the applicable edge characteristic, quality range, material and thickness.
- Choosing a gas from the material name alone, without verifying the route and downstream edge requirements.
- Inspecting only the top face and missing dross on the underside.
- Treating a clean-looking edge or visible colour as proof of dimensions or material properties.
Numbers to check before quoting
Before quoting, identify the drawing revision, material and thickness, required edge features and downstream finishing. Tie the trial specimen and original results to agreed measurement locations and methods. Where ISO 9013 applies, agree the edition and quality requirements. Use the weight calculator for material or logistics calculations; weight and machine accuracy do not establish cut-edge quality.