What shearing is
Here, shearing means cutting sheet in a straight line with a moving blade against a fixed bed blade. It is suited to blanks, strips and straight edges when the required part permits a sheared edge.
Blade clearance is the lateral gap between the upper and lower cutting edges. Use the selected machine instructions to identify how that gap is defined and checked for the actual material and thickness, including any stated single-side or total-clearance convention. Keep it separate from cut length along the blade, blank width from the cutting line to the backgauge, and shear angle: the inclination between the blades.
Check thickness, blade clearance and cut-edge quality
| Item | Statement | Basis |
|---|---|---|
| Blade clearance | Use the machine manual for the material and actual thickness; identify single-side or total clearance | Machine-specific setup |
| Thickness capability | Material/model specific | Supplier process envelope required |
| Edge quality | Straight edge with burr; depends on clearance and blade condition | Process behaviour |
| Cut shape | Straight cuts only | Process limit |
| Machine accuracy | GB/T 14404-2024 covers shearing machine accuracy | Published standard |
Choose blade clearance from the instructions for the actual machine, material and thickness, then confirm the cut edge against the required result. Recheck the clearance when moving from mild steel to stainless or high-strength steel.
Before comparing settings or cut samples, identify the material grade, condition and lot, actual thickness, cut length along the blade, and strip or blank width. Keep these with the machine model and its rating conditions, blade identification and condition, the clearance definition and permitted setting from the machine instructions, and the required edge and inspection method.
How the cut behaves
- A shear produces a straight edge with a burr. The burr size depends on clearance, blade condition and material.
- Too little or too much clearance changes the edge and can increase the burr or the distortion.
- A narrow strip can curl or twist if the cut releases internal stress.
- The cut edge is work-hardened in some materials, which matters if the edge will be bent afterwards.
Treat the cut face, burr and strip shape as observations to compare with the job requirement. Appearance alone does not establish the clearance or prove that the part is acceptable.
Failure modes to watch
| Observation | Possible checks | Evidence to retain |
|---|---|---|
| Heavy burr or rough edge; possible need for deburring | Review the machine clearance definition and recorded setting together with blade condition and material | Material lot and actual thickness; actual setting; burr side, location and size; edge photographs |
| Curl or twist on a narrow strip | Review strip width, material condition and released internal stress, sheet support and the existing shear angle | Strip width, material identity and observed distortion |
| Cut out of square or blank width varies | Review the reference edge, backgauge positioning, squaring guides and sheet support | Dimensions at marked positions and the agreed squareness inspection |
| Edge changes during a long batch | Review blade condition and whether material or thickness changed between samples | Batch and time identification; early and later samples and their material records |
These are possible checks, not a fault-to-setting recipe. A rough edge or heavy burr does not identify one cause, prove that clearance is too large or too small, or tell you which adjustment to make. Review the material lot, actual thickness, blade condition, recorded settings and the selected machine instructions together before an authorised check or change.
Trial-cut release record
| Field | Record |
|---|---|
| Inputs | Grade/lot, actual thickness, cut length and edge requirement |
| Machine boundary | Rated material/length/thickness from machine instructions; blade ID/condition and approved clearance |
| First piece | Cut width at marked positions, squareness by agreed method, burr side/size and strip distortion |
| Disposition | Accepted to stated requirement, or hold with observed fault; retain actual setting and recheck after authorised change |
Confirm capacity for the actual material, machine and process. Record the first piece’s edge and dimensions against the drawing and agreed method, with the applicable machine and tool instructions for settings and limits.
When to choose shearing
- Choose shearing for straight cuts, rectangular blanks and strip.
- Choose it when the edge requirement is a normal sheared edge and a burr can be accepted or removed.
- Do not choose it for contours, holes or a profile that needs a laser or a punch.
- Do not choose it when the edge will be visible and a laser-cut finish is required.
Machine selection
The equipment decision is narrower than a press brake decision: a shear only makes straight cuts, so the question is how thick, how wide, how accurate and how clean the edge has to be. The machine is specified from the cut.
Rated thickness and material strength
A machine thickness rating applies to stated material and machine conditions; it is a limit to verify, not a target or the nominal thickness of the sheet.
Required cutting force depends on material shear strength, thickness and the extent of material engaged in the cut. A higher-strength material can demand more force at the same thickness.
Confirm actual material, thickness and cut length together against the selected model rating; a shorter cut does not automatically permit thicker material.
- Read the rated thickness together with the material it is rated in, not as a bare number.
- Check the maximum cut length and the maximum thickness as a pair, because the force depends on both.
- Ask how the rating changes for stainless steel, aluminium and high-strength steel.
- Keep margin for material that arrives at the top of its thickness tolerance.
- Do not use the machine above its rating to save a second pass; the blade, the frame and the hold-down all take the overload.
Blade clearance and how it is adjusted
Blade clearance affects how the material separates. Too little clearance can raise cutting force and damage the edge; too much can draw sheet into the gap and leave a heavier burr, rougher edge or more distortion.
These effects are not a diagnosis on their own. Use the machine-defined gap convention and material-specific instructions, then check the resulting edge against the job requirement. Clearance is a process setting, separate from the dimensions specified on the drawing.
- Manual adjustment uses shims or a screw setting and is common on simpler machines; it is slow when the job changes material often.
- Motorised adjustment moves the blade or the table to a set value from the control.
- Automatic adjustment follows a stored setting for a material and thickness, which reduces the chance of a wrong clearance between jobs.
- Whichever method is fitted, confirm the setting on a trial cut and check the burr before the batch is released.
- Record the clearance used for each material and thickness, so that a repeat job starts from a known setting.
Backgauge, squaring and sheet support
The backgauge sets the cut width by holding the sheet against a stop. A squaring arm sets the sheet square to the blade, and a front support or a rear support table carries the sheet so that the operator is not holding the full weight through the cut.
On a large sheet the support arrangement matters as much as the gauge: a sheet that sags or lifts during the cut produces a cut that is not square even when the gauge is set correctly.
- Check the backgauge stroke against the widest cut the shop expects, not only against the current part.
- Confirm that the gauge can be set and locked repeatably for the batch size.
- Plan support for the full sheet and for the offcut, because the offcut can drop or twist as the cut opens.
- Use a squaring arm or a positive stop when the first cut has to be square to the edge.
- Check how narrow a strip the machine can hold safely; a narrow strip can curl or twist when the cut releases internal stress.
Shear angle and cut quality
The moving blade is usually inclined to the bed blade so that the cut progresses along the sheet rather than engaging the full length at once. A larger shear angle reduces the length engaged at one time and can lower peak force, with a greater tendency to distort the sheet. A smaller angle can give a flatter result while requiring more force.
Some machines have an adjustable angle and others a fixed angle. This does not mean the geometric cut length along the blade changes.
A sheared edge differs from a machined or thermal-cut edge. Specify the permitted burr and edge squareness for visible, welded or painted parts before choosing the process. Any required deburring adds another operation; compare the actual edge requirement rather than expecting a shear to reproduce a laser-cut finish.
Machine selection checklist
- State the material, the maximum thickness and the maximum cut length as a set.
- Confirm the blade clearance adjustment and whether it can follow the material mix.
- Check the backgauge travel, the squaring arrangement and the sheet support.
- Decide whether a fixed or an adjustable shear angle suits the parts.
- Confirm the machine accuracy requirement against the applicable standard and a trial cut.
- Compare the shear with the cutting machine already on the floor before adding a second cut process.
For the model rating and quoted blade, positioning and support configuration, continue to Shearing machine selection.
Shearing against laser and plasma
| Criterion | Shear | Laser or plasma |
|---|---|---|
| Cut shape | Straight cuts only | Contours, holes and profiles |
| Edge | Sheared edge with burr | Thermal cut edge with its own quality class |
| Straight-cut task | Dedicated straight-line blank or strip cutting | Contours and profiles as well as straight cuts; compare actual job and handling time |
| Setup | Blade clearance and backgauge | Nesting, program and gas or assist settings |
Start with the required geometry and edge. A shear is a candidate for rectangular blanks and strips; holes and contours need another process such as laser cutting or punching. Where both processes are used, compare the straight-cut workload, handling and any deburring before assigning the first blanking cut to a dedicated shear.
Common mistakes
- Using one blade clearance for every material and thickness.
- Nesting parts too close to the cut line and losing the edge to burr or distortion.
- Expecting a laser-like edge from a shear.
- Ignoring the machine accuracy standard when the part has a dimensional requirement.
- Treating burr alone as proof of incorrect clearance, without checking material, blade condition and the machine instructions.
Numbers to check before quoting
Use the weight calculator for blank weight; weight does not establish cutting capacity. GB/T 14404-2024 concerns machine accuracy: its scope does not replace the drawing requirements for part burr, edge condition or acceptance. Keep clearance with the machine-specific process instructions and recorded trial, separate from drawing dimensions.