What the V-die is
The V-die is the lower tool on a press brake. Its V-shaped opening supports the sheet while the punch presses the bend into it. In air bending the sheet does not bottom out in the die, so the opening has a direct effect on the formed geometry.
How it works
In conventional air bending, the sheet rests on the die shoulders while the punch presses it into the opening without bottoming out. The opening influences the inside radius together with the material, actual thickness and tooling geometry. With other conditions comparable, a smaller opening generally raises force demand and lowers the flange estimate; a larger opening generally increases the formed radius and flange estimate. These trends do not guarantee a particular radius or sufficient support.
- Starting values: take the opening, inside radius range and minimum flange from the calculator for the material and thickness.
- Selection basis: the opening has to suit the required radius and flange, not a remembered thickness multiple.
- Minimum flange: limited by the V opening and by the punch geometry.
- Force rises as the V opening gets smaller. Convert total force F to line load q = F/L using actual engaged length L in metres, then compare like units with the tool rating and check all local/concentrated-load limits.
Selection guidance and failure modes
- Start with the material grade, condition and actual thickness; compare the calculator starting opening with the drawing radius and shortest flange, then check actual support and the applicable assembly load limits. A calculator material category does not approve a specific grade.
- A V opening that is too small can make a short flange possible but drives the required force up and may overload the tooling.
- With other conditions comparable in conventional air bending, a larger V opening generally increases the inside radius and minimum flange estimate. If these conflict with the drawing, review the proposed tooling combination.
- Using one V opening for every material ignores the difference between mild steel, stainless steel and aluminium, and can misstate both radius and tonnage.
- A punch with a small tip in a wide V die does not guarantee a small inside radius; the opening, material and actual tooling jointly constrain the result.
Multi-V dies: several openings in one block
A multi-V die carries more than one V opening in the same lower-tool block. The block is turned or indexed so the required opening sits under the punch, so changing thickness can mean changing the active opening instead of changing the die. Different V openings occupy positions across the block cross-section. This does not by itself shorten the bend length; verify the continuous usable length of the selected groove from its drawing.
- Choose a multi-V die for job-shop work with frequent thickness changes and parts within the documented usable length of the selected groove.
- For a long bend, confirm that the selected groove and any joined segments provide the required continuous support; multi-V construction alone does not rule it out.
- Confirm which opening is under the punch and that the block is locked before the first stroke.
- Measure the opening across the V and compare the required tonnage per metre with the rating for the selected opening and the usable length.
- Do not infer usable length or rating from block dimensions alone; check the selected groove and assembly documents.
The V-die opening calculator suggests a starting opening and the tonnage calculator estimates total force F; divide F by actual engaged length L in metres for line load F/L. If the part is long, confirm that the documented continuous usable length covers the bend.
Load and clearance release worksheet
| Check | Record and compare |
|---|---|
| Units | Estimated total F in kN; engaged bend length L in m; distributed estimate q = F/L in kN/m, L > 0 |
| Actual assembly | Punch, active die opening, holder, adaptor and machine IDs; each applicable rating with units |
| Short or interrupted loading | Use manufacturer limits for short segments, cut-outs, eccentric loads and minimum engagement; do not assume uniform loading |
| Clearance | Check full bend sequence against part, tool, clamp and machine geometry using the manufacturer-approved safe method |
| Release | Keep the estimate, rating documents and first-part unloaded angle/radius; do not infer safety from machine total force alone |
As a unit-conversion example, assume 100 kN is spread uniformly over 0.50 m: the average line load is 200 kN/m. Use actual engaged length for the job and compare the result with applicable tool, assembly and local loading limits. [A1]
Setup and inspection notes
- Measure the opening across the V, not the die width or the slot spacing on the bed.
- Compare the required tonnage per metre with the die and punch rating before the first bend.
- The minimum flange estimate is a first screen, not a guarantee of die support. Check whether the drawing uses an outside theoretical sharp corner or a straight tangent length, then compare actual die shoulder opening and radii, continuous support and punch geometry. Below the estimate, do not release the part on that estimate or conclude that it cannot be made; the tooling combination needs review.
- Run a trial bend in the production material and record the unloaded inside angle and inside radius; correct the selection before releasing the batch.
Work the numbers
Enter material and actual thickness for a starting opening, radius range and flange estimate. Enter the proposed actual V opening to update the flange estimate only: the displayed radius still follows the material/thickness rule and does not validate the radius made by that die. For total force F, use the selected V opening and actual engaged length in the Press brake tonnage calculator; divide F by engaged length L in metres for F/L and compare with actual assembly and local load limits. The PDF lists reference starting values by thickness and material.