Inspecting a used press brake is mostly a question of knowing which checks belong to the buyer, which belong to a qualified person, and which cannot be answered at all without documents the seller may not have. The visit itself is the easy part. The expensive mistakes are made by buyers who start at the tooling and never ask who has serviced the machine, what control is inside it, or whether the parts to keep it running can still be bought.
Start with the documents
- Identity: the nameplate and the serial number, matched against the model and year the seller states, and against the manual for that model.
- Ownership and service history: who owned it, who maintained it, and whether there is a record of what was done and when.
- Conformity and delivery documents, where the seller has them, so that the machine's original configuration can be compared with what is fitted now.
- Support: whether the manufacturer or a representative still supports that model and control, and where spares come from.
- Cost of the gaps: what it would take to replace missing documents, obsolete controls or absent guarding before the machine earns money.
A seller who cannot produce a manual, a service history or a clear serial number is not necessarily selling a bad machine, but the buyer is now pricing an unknown. That price belongs in the negotiation before the visit, not in a repair bill afterwards.
What can be checked from outside
With the machine stopped and the seller's operator present, a buyer can look at the frame and the weld seams for cracks or previous repairs, at the hydraulic area for leaks and at the floor for stains, at the tooling for damage and at the clamping for wear, at the guards and protective devices for missing parts or defeat, and at the control for stored alarms. The history of those alarms can be read from the control by someone who knows it. All of this is observation: it does not include opening an enclosure, removing a cover or reaching into the tooling area.
What belongs to a qualified person, with the machine isolated
The inside of an electrical cabinet, the condition of the wiring and drives, the hydraulic valves and cylinders, the condition of the ram guides, and the mounting and condition of the protective devices are inspected by a qualified person, under electrical safety rules and with the machine isolated under a lockout procedure — isolation points locked and every form of stored energy released, restrained or blocked, with the safe state verified before anything is opened. A buyer should not open a live cabinet and should not operate a machine with a guard removed to see how it runs. If the seller will not allow an isolated inspection, that refusal is information about the machine.
Testing whether a protective device functions is a separate step from inspecting it with the machine isolated. Once the machine is back together, a controlled functional test is run by trained personnel following the manufacturer's procedure — not by a buyer presenting a hand or an object to a moving ram — and a device that fails is put out of service, with the machine kept out of service until it is repaired and verified. The safety devices article explains what each device covers and what it does not.
Test bends, run in a controlled way
Test bends are the part of the visit that shows how the machine behaves on the buyer's own work: a simple part, tooling that is known to be in good condition, and a program checked before the first stroke. The machine is run by a trained operator, the sequence is written down, and the parts are measured and kept. A recorded sequence of bends shows whether the angle and the position repeat over the run; it is not a substitute for the manufacturer's acceptance test, and no fixed number of bends turns it into one.
A bend test also does not prove the protective devices work. Those are two different questions with two different procedures, and a machine can produce good parts while a device is defeated.
The costs that are easy to miss
| Item | Question to answer before buying |
|---|---|
| Control and software | Is the control still supported, and can programs be transferred to it? |
| Spares | Which wear parts are still available, and at what lead time? |
| Tooling | Does the tooling match the buyer's parts, and is it standard or proprietary? |
| Guarding | Is the machine's guarding complete, and what would completing it cost? |
| Transport and installation | What does moving, foundation work and recommissioning add to the price? |
| Hydraulic system (hydraulic machines) | When were the oil and filters last changed, and is the pump still serviceable? |
For a used machine offered in the European Union, the buyer checks which market it is destined for, when and by whom it was first placed on the market, and what modifications it has had since; the party placing it on the market and a competent professional then confirm which conformity route applies. The CE documentation guide is reference material on the documents a buyer can ask for. Neither this article nor that guide decides the legal status of a particular used machine.
A used machine and a new one are often compared on the purchase price alone. Comparing a used machine with the new press brake range and with a quote for the parts you actually bend puts the purchase price, the delivery and the specification on the same page.