Who should use this checklist?
Use this checklist when buying a press brake that will be placed on the EU market. Purchasing staff coordinate document delivery; engineering and safety staff review the technical content. The manufacturer prepares the technical documentation, and the manufacturer or its authorised representative issues the declaration of conformity as provided by the applicable legislation. If you buy through a dealer, ask the dealer to obtain the relevant documents from the manufacturer.
Five questions to answer before accepting the documents
- Which machine do the documents cover? Match the model, serial number and configuration to the order and the delivered machine.
- Who takes responsibility? Check the manufacturer, signatory and signing details on the declaration of conformity.
- What supports the declaration? Identify the legislation and standards cited, who can answer technical questions, and which supporting records can be supplied or reviewed.
- How will the machine be used safely? Check that the instructions cover the supplied configuration, installation, operation, maintenance and safety requirements in the language required at the destination.
- What is still outstanding? List missing documents and unanswered questions, with an owner and a date for each response.
What to request, and from whom
| Document | What the buyer should check | Who supplies or holds it |
|---|---|---|
| Declaration of conformity | Machine identification, responsible manufacturer, applicable legislation and signing details. | Request it from the supplier; it is issued by the manufacturer or its authorised representative under the applicable legislation. |
| Instructions for use | Installation, operation, maintenance and safety information for the supplied configuration, in the required language. | The supplier arranges delivery with the machine. |
| Nameplate and configuration record | Consistency between the machine, order, declaration and instructions. | Confirm the nameplate details and ordered configuration with the supplier. |
| Relevant test or validation records | Evidence for specific technical questions, including the model, configuration and test conditions covered. | Ask the supplier to coordinate with the manufacturer; agree what can be supplied or made available for review. |
| Technical documentation | The manufacturer’s technical basis for demonstrating conformity. | Prepared and retained by the manufacturer for provision to the competent authorities as required. Agree separately which supporting records the buyer needs. |
The declaration and instructions delivered with the machine have a different purpose and delivery scope from the manufacturer’s full technical file. Risk assessments, design calculations and detailed drawings form part of that file. Agree which supporting records are needed for your technical questions, how they may be reviewed, any confidentiality arrangements and the delivery milestones.
MD or MR: establish the applicable framework
On this guide’s review date, 2026-11-05, Directive 2006/42/EC (MD) remains the current machinery framework. The corrected consolidated text of Regulation (EU) 2023/1230 (MR) states that it applies from 2027-01-20 and repeals the MD with effect from that date. Determine the actual product, configuration and placing-on-the-market situation before selecting a declaration template; do not simply change “EC” to “EU” on an old document.
| Question | MD — Directive 2006/42/EC | MR — Regulation (EU) 2023/1230 |
|---|---|---|
| General timing in the corrected text | Current before the MR changeover; repealed with effect from 2027-01-20. | Applies from 2027-01-20, subject to its stated earlier article-specific dates and transitions. |
| Complete-machinery declaration | EC Declaration of Conformity: Annex II, Part 1.A. | EU Declaration of Conformity: Annex V, Part A. |
| Technical documentation | Use the applicable MD Annex VII requirements and the machine’s actual conformity-assessment route. | Annex IV, Part A for machinery and related products; Part B separately covers partly completed machinery. |
| This guide’s scope | EC declaration fields and a practical evidence-index approach. | Full Annex IV Part A field list and EU declaration fields. |
| Not decided by this table | Product scope, conformity route, notified-body need or legal status of an individual machine. | The same case-specific questions; classification and transitions require their own review. |
Article 52 also preserves specific transitions: Member States must not impede the making available of products placed on the market in conformity with the MD before 2027-01-20, subject to the article’s market-surveillance wording; EC type-examination certificates and approval decisions issued under MD Article 12 remain valid until they expire. Do not reduce “placed on the market” to an invoice, shipment or installation date without checking the legal facts.
How to check the standards cited in the declaration
| Document or record | What it can establish | What it cannot establish by itself |
|---|---|---|
| Commission harmonised-standards list | The cited standard edition, amendments and the list’s legal-effect dates. | The clauses of the standard, application to a particular machine or a manufacturer’s conformity. |
| Lawfully obtained EN standard text | The actual requirements and test material available for qualified review. | That every clause applies or that a machine meets them without assessment and evidence. |
| Technical documentation | How the manufacturer demonstrates conformity for the identified product and configuration. | Conformity when required elements, results or responsibility are missing. |
| EC/EU Declaration of Conformity | The responsible party’s formal declaration and the references used. | An independent certificate in every case; a signature cannot repair an unsupported technical file. |
| Type-examination certificate, where applicable | The result and scope of the identified examination route. | Automatic coverage of a different model, configuration or later modification. |
Ask for the full standard number, edition and amendments, and whether it was applied in full or in part. Engineering staff should check its scope against the machine’s intended use and configuration. Where the actual requirements need review, use the authorised acquisition channels in the standards index.
Check editions and access routes in the standards index.
Track supporting records for technical review
Use this index to follow up supporting records with the manufacturer’s technical staff; agree access to individual records rather than expecting delivery of the entire technical file. Give every agreed item an owner, revision and status. “Received” means an identified document was received; it does not mean its technical content has passed review. Keep proprietary detail in the controlled manufacturer file where necessary, while making the index and review conclusions specific enough to audit.
| Evidence group | Minimum index entry | Review question |
|---|---|---|
| Identity and scope | Manufacturer, model, serial/batch, configuration, intended use and foreseeable misuse. | Do the declaration, drawings, instructions and tests identify the same machine and use? |
| Legal and EHSR matrix | Applicable legislation, requirements, conformity route and justification for exclusions. | Is each applicable requirement assigned evidence rather than a blanket statement? |
| Risk and protection | Risk-assessment revision, protective measures, residual risks and validation links. | Do safeguards and instructions correspond to the delivered configuration? |
| Design and software | Drawing/circuit index, safety functions, control/software versions and relevant calculations. | Are revisions traceable to what was tested and supplied? |
| Standards and specifications | Exact editions, amendments, full/partial application and alternative specifications. | Are references accurate, and is partial application identified? |
| Tests and production | Raw reports/results, test configuration, acceptance criteria, production consistency and change control. | Are unsuccessful, untested and deferred items visible? |
| Instructions and declarations | Instruction revision/language set, incorporated-product declarations and final EC/EU declaration. | Is the correct annex/template used and signed by the responsible party? |
| Open items | Missing evidence, technical query, owner, due date and closure evidence. | Can a reviewer distinguish missing, not applicable and reviewed-accepted items? |
Technical reference: what the manufacturer’s file should contain
The following is a concise field guide to Annex IV, Part A for machinery and related products; it is not a substitute for the official text. Part A says the documentation must specify the means used to ensure conformity with applicable Annex III EHSRs and include at least these elements. Partly completed machinery has a separate Part B and is not reduced to the complete-machine checklist here.
| Official field | Evidence group | Concise content guide |
|---|---|---|
| Annex IV Part A (a) | Machine and intended use | Complete description of the machinery or related product and its intended use. |
| Annex IV Part A (b) | Risk assessment and protective measures | Procedure carried out; applicable essential health and safety requirements (EHSRs); protective measures for each applicable EHSR and, where appropriate, residual risks. |
| Annex IV Part A (c) | Drawings and schemes | Design and manufacturing drawings and schemes for the machine, components, sub-assemblies and circuits. |
| Annex IV Part A (d) | Explanations | Descriptions and explanations needed to understand the drawings, schemes and machine operation. |
| Annex IV Part A (e) | Harmonised standards or common specifications | References applied in design and manufacture; where application is partial, identify the parts applied. |
| Annex IV Part A (f) | Other technical specifications | Where harmonised standards or common specifications are absent or only partly applied, describe the other specifications used to meet each applicable EHSR. |
| Annex IV Part A (g) | Calculations, tests and examinations | Reports and/or results used to verify conformity with the applicable EHSRs. |
| Annex IV Part A (h) | Production conformity | Means used during production to ensure that produced machines conform to the design specifications. |
| Annex IV Part A (i) | Instructions | Copy of the instructions for use and the information required by Annex III, section 1.7.4. |
| Annex IV Part A (j) | Incorporated partly completed machinery | Where appropriate, EU declaration of incorporation and assembly instructions. |
| Annex IV Part A (k) | Incorporated products | Where appropriate, EU declarations for incorporated machinery, related products and products covered by other Union harmonisation legislation. |
| Annex IV Part A (l) | Series production | Internal measures that keep series-produced machines in conformity with the Regulation. |
| Annex IV Part A (m) | Safety-related software | Source code or programming logic upon a reasoned request from a competent national authority where necessary for its EHSR compliance check. |
| Annex IV Part A (n) | Sensor-fed, remotely driven or autonomous systems | Where appropriate, general characteristics, capabilities and limitations of the system, data, development, testing and validation processes when safety-related operations are controlled by sensor data. |
| Annex IV Part A (o) | Safe assembly and putting into service | Manufacturer research and test results on components, fittings or the machine used to determine whether its design or construction permits safe assembly and putting into service. |
Checking the declaration: MD and MR fields
These are two different 1–10 structures. Do not reuse the MD numbering as if it were the MR template. “Where appropriate” and “where applicable” fields still require a conscious applicability decision; they are not fields to delete without review. The declaration number shown by the MR template is optional.
MD Annex II, Part 1.A — EC Declaration of Conformity
| No. | Required particular |
|---|---|
| 1 | Manufacturer and, where appropriate, authorised representative: business name and full address. |
| 2 | Name and address of the person authorised to compile the technical file, who must be established in the Community. |
| 3 | Machine description and identification: generic denomination, function, model, type, serial number and commercial name. |
| 4 | Express statement that the machinery fulfils all relevant provisions of the Directive and, where appropriate, equivalent statements for other applicable Directives and/or relevant provisions, using OJ references. |
| 5 | Where appropriate, notified body and EC type-examination certificate details under Annex IX. |
| 6 | Where appropriate, notified body that approved the full quality assurance system under Annex X. |
| 7 | Where appropriate, references to the harmonised standards used. |
| 8 | Where appropriate, references to other technical standards and specifications used. |
| 9 | Place and date of the declaration. |
| 10 | Identity and signature of the person empowered to draw up the declaration for the manufacturer or authorised representative. |
MR Annex V, Part A — EU Declaration of Conformity
| No. | Required particular |
|---|---|
| 1 | Machinery or related product, including product, type, model, batch or serial number; or substantially modified machinery or related product. |
| 2 | Name and address of the manufacturer and, where applicable, its authorised representative. |
| 3 | For specified permanently installed lifting machinery that can only be assembled at the place of use, the address of that place. |
| 4 | Statement that the declaration is issued under the sole responsibility of the manufacturer. |
| 5 | Object of the declaration with traceable identification; a sufficiently clear colour image may be included where necessary. |
| 6 | Statement that the object is in conformity with the identified Union harmonisation legislation. |
| 7 | Applied harmonised standards or common specifications with OJ publication dates, or other technical specifications with dates; identify parts applied when application is partial. |
| 8 | Where applicable, notified body, EU type-examination certificate and the subsequent Module C, G or H procedure. |
| 9 | Where applicable, statement that the machinery is subject to internal production control (Module A). |
| 10 | Additional information, signed-for/on-behalf-of details, place and date of issue, name, function and signature. |
The MD’s field 2 explicitly names the person established in the Community who is authorised to compile the technical file. The MR’s list is organised differently, adding, among other things, the sole-responsibility statement, traceable object and dated standards/common-specification references. Compare the official annexes rather than assuming a one-to-one row conversion.
Agree document access and delivery milestones
| Item to agree | Scope to confirm | Follow-up status |
|---|---|---|
| Quotation documentation basis | Destination market, machine/configuration identity, intended use, applicable legal framework and document-delivery milestone. | Agreed / open / changed |
| Documentation index | Document title, revision, date, owner and machine/configuration coverage for every item. | Received / reviewed / missing |
| Requirements and standards matrix | Applicable EHSRs or MD requirements, exact standard editions/amendments, full or partial use and supporting evidence. | Complete / gap / query |
| Risk and safety validation | Risk-assessment reference, safety-function configuration, applicable calculations, validation reports and residual-risk instructions. | Reviewed / untested / query |
| Drawings, program and instructions | Controlled drawing/circuit list, relevant software version, manual revision and required language set. | Matched / mismatch / missing |
| Test and inspection evidence | Procedure, acceptance basis, machine and specimen setup, raw results, deviations and responsible reviewer. | Pass / fail / untested / deferred |
| Declaration pack | Correct EC or EU annex, incorporated-product declarations where relevant and responsible signatory. | Draft / signed / incorrect basis |
| Production and change control | Series-production consistency measures and the trigger for reassessing a changed configuration. | Defined / missing |
| Acceptance handover | Order-specific inspection records, kept separate from legal conformity conclusions. | Agreed / open / closed |
Keep order-specific inspection records in the machine acceptance guide, separate from legal conformity conclusions. For proprietary technical information, agree a summary, on-site access or a confidential review. Agree what will be indexed, reviewed, supplied or made accessible, who may review it and how confidential material is handled before the delivery milestone.
Use these document requirements to frame the quotation and acceptance discussion for Press brake range; confirm the applicable obligations for the destination market and supplied configuration.
Review gaps before relying on the documentation pack
- Match the legal framework, declaration title and annex to the actual placing-on-the-market and transition facts.
- Match manufacturer, model, serial/batch, configuration and intended use across declaration, nameplate, drawings, instructions and test reports.
- Check exact standard years and amendments, full versus partial application, and the evidence behind each claimed requirement.
- Distinguish a manufacturer declaration, a test report and a notified-body certificate; record the actual conformity-assessment route.
- Keep failed, untested, deferred and missing items visible with an owner and closure evidence; do not convert them into a summary pass.
- Recheck official consolidated legislation and the Commission list before signature or shipment decisions; a downloaded snapshot does not update itself.
Why two dates appear: original OJ and corrected consolidation
The original Official Journal text and the corrected consolidated text serve different evidence roles. The original shows what was published on 2023-06-29. The consolidation shows later amendments and corrections inline. Its cover identifies C1 as “Corrigendum, OJ L 169, 4.7.2023, p. 35 (2023/1230)”. C1 changes the relevant January dates from 14 to 20 January 2027. For current date reading, use the corrected text and retain the original when documenting the difference.
| Provision | Original OJ text | Consolidated text with C1 |
|---|---|---|
| Article 51(2): MD repeal | With effect from 2027-01-14. | With effect from 2027-01-20. |
| Article 52(1): products already placed on the market | Before 2027-01-14. | Before 2027-01-20. |
| Article 54: general application | From 2027-01-14. | From 2027-01-20. |
| Evidence role | Original publication, 29 June 2023. | Consolidation dated 2026-07-27; C1 and later amendments are visibly identified. |
This is why quoting 2027-01-14 as the current general application date is outdated, while hiding the original date would make documentary comparison harder. Recheck EUR-Lex before relying on this page after its review date.
Scope and review record
- Reviewed
- 2026-11-05 against the official original and consolidated texts linked below.
- MR consolidation used
- 02023R1230 — EN — 27.07.2026 — 002.001, including C1 and later amendments shown on its cover.
- MD consolidation used
- 02006L0042 — EN — 30.05.2026 — 006.001.
- What this guide covers
- Documentation fields and evidence preparation for complete machinery; not a product classification, legal opinion or conformity assessment.
- RAGOS product status
- No statement is made here that a RAGOS machine, another supplier’s machine or a particular configuration conforms to the MD, MR or any EN standard.
The downloads library contains engineering records for inspection and record keeping. Those worksheets are not CE declarations or substitutes for the official legal texts.