What welding is

Welding joins sheet and formed parts into frames, enclosures, tanks and other assemblies by heating the joint. Start with the joint’s load, sealing and appearance requirements, then check the material, fit-up and weld access. Local heating and cooling can change the final shape, which is why sequence and restraint matter alongside weld quality.

When to choose welding

  • Welding is an option for permanent joints where the drawing requires load transfer, sealing or an assembled shape that cannot be made as one part. Confirm the actual joint requirements rather than assuming that a continuous weld always needs to be leak-tight.
  • Where bolting or riveting meets the assembly requirements, compare its effects on access, finish and final dimensions. A coated sheet needs a suitable joining and coating-treatment route; coating removal and restoration depend on the coating, joint and applicable procedure.
  • A specified continuous weld is not interchangeable with intermittent welds. Any proposed change needs assessment and confirmation under the joint design and applicable welding procedure; approval alone is not evidence of joint performance.

Review final angles with bending and curved geometry with rolling. Check the formed-part dimensions, weld access and joint requirements together when planning the fabrication route.

Compare Laser welding machines and Welding robots against the joint and production task, including seam access, fit-up, fixtures and the required welding procedure.

Check distortion, material preparation and joint thickness

ItemWhat to verifyBasis
Distortion driverHeat input and its distribution, together with joint geometry and restraintThermal process behaviour; not a one-variable prediction
Distortion controlA suitable sequence and fixture; intermittent welds only where the joint design allows themReview under the applicable procedure and compare representative parts
Galvanized steelIdentify the coating, suitable preparation/consumables and the required protection of the affected areaMaterial, coating and procedure requirements
AluminiumConfirm alloy, surface/oxide preparation and suitable consumablesApplicable material and welding procedure
Thickness capabilityActual material, joint, procedure and equipment configurationSupplier process envelope and representative-joint evidence required

Confirm the joint design, material and thickness with the specified welding procedure and required inspection. Check the finished joint against its drawing requirements.

Heat input and distortion

Local heating and cooling can produce uneven expansion and contraction. Material properties, joint geometry, fit-up and restraint affect the type and degree of distortion; heat input or pass count alone cannot predict how far a part will move. [A2]

  • Review weld position and extent, joint gaps, the recorded sequence and support/fixture arrangement together. A planned sequence aims to manage shrinkage; it does not guarantee that opposite sides cancel each other.
  • Intermittent welds leave unwelded intervals. They are not spot welding and cannot simply replace a specified continuous or leak-tight joint. Discuss them only where the joint design and applicable procedure permit them.
  • Clamps can limit movement during welding while leaving locked-in stresses. Compare dimensions after cooling and fixture release as required by the drawing; a flat panel while clamped is not proof of the released result. [A3]

Material preparation

  • Galvanized steel: identify the coating and confirm preparation, consumables and any restoration of corrosion protection under the applicable requirements; do not assume one coating-treatment route suits every joint.
  • Aluminium: confirm the alloy and the specified surface/oxide preparation and consumables for its procedure.
  • Carbon steel: review cleanliness and the procedure’s treatment of oil, rust and mill scale that could affect joint consistency.
  • Stainless steel: confirm the material, preparation and consumables with the responsible workshop personnel.

Use the sheet metal materials guide to review material identity; it does not replace the welding procedure.

Identify coatings and assess exposure before welding or coating removal. OSHA notes that outdoor work alone may not provide adequate ventilation. Have a competent person assess the actual workplace and specify extraction and other controls for the work. [A1]

Failure modes to watch

The heat-affected zone (HAZ) is parent metal that has not melted but whose properties may change during the welding thermal cycle. Its presence alone does not establish a defect. Assess material and joint conformity against the specified requirements; visible discoloration alone does not establish HAZ properties. [A4]

These observations suggest checks, not a diagnosis. Before comparing dimensions, confirm the same datums, measurement state and support/clamping conditions. An unexplained difference remains open for investigation rather than being attributed automatically to welding settings.

Observation or recorded issueCandidate checksRequirements to consult
Panel dimensions or angle differCompare the marked positions before welding and after cooling/release, with comparable datums and supportFinal drawing dimensions and measurement requirements
Local bowing or uneven movementReview pre-weld shape, fit-up, joint geometry, sequence and restraint records togetherApplicable process and drawing; keep other causes open if records do not explain it
Coating damage or exposed steelIdentify the affected area and the specified finish/protection routeCoating restoration and inspection requirements for this assembly
Material/consumable differs from the applicable procedure, or HAZ inspection is specifiedCheck material identity and the relevant procedure/inspection recordsDrawing and applicable inspection requirements; HAZ visibility alone is not a trigger or acceptance criterion

Visual and dimensional observations do not establish internal integrity, strength or leak tightness. Where those results are required, use the specified inspection and acceptance requirements; this table supplies no test method or acceptance limit.

Common mistakes

  • Replacing a specified continuous joint with intermittent welds because they appear to reduce distortion, without resolving the joint design and procedure requirements.
  • Predicting movement from heat input or pass count alone, or inspecting only while the part remains clamped.
  • Proceeding without checking surface/coating preparation and material-compatible consumables, including aluminium oxide preparation and protection of affected coated areas.
  • Adding weld to a distorted assembly as an unreviewed correction instead of investigating its records and the approved route for any repair.

Joint release and before/after record

StageRecordRelease question
Before weldingDrawing/weld requirement, material/coating, joint fit-up and approved procedureAre joint continuity, preparation and fume controls agreed?
Trial assemblyFixture/support, sequence, consumable and procedure settingsDoes the qualified procedure permit the proposed sequence?
After cooling and fixture releaseSame marked dimensional positions, support condition and visual observationsDoes the assembly meet its specified dimensions and weld requirements?

Compare the three stages using the same datums and stated support or fixture conditions. Keep the drawing revision, material/coating, joint identity, measurement positions and welding sequence with the readings. Follow the applicable procedure and inspection requirements for the actual joint and restraint conditions. [A3]

Numbers to check before quoting

The weight calculator estimates the sheet or blank weight entered; it does not automatically include weld metal or accessories, or establish measured finished weight. The standards index is equipment-reference navigation, not a welding procedure or joint acceptance specification.