[{"data":1,"prerenderedAt":181},["ShallowReactive",2],{"page-content:en:knowledge\u002Ftooling\u002Fpunch":3},{"meta":4,"hero":10,"body":19,"references":151,"related":164,"cta":177},{"path":5,"title":6,"seoTitle":7,"description":8,"updated":9},"\u002Fknowledge\u002Ftooling\u002Fpunch\u002F","Press brake punch","Press Brake Punch Selection: Tip and Clearance | JS Ragos","The upper tool shapes the bend and provides clearance for formed flanges. Compare tip shape, body height, neck profile and clamping interface against the full bend sequence.","2026-11-05",{"kicker":11,"title":6,"subtitle":8,"facts":12},"Knowledge base \u002F Tooling",[13,16],{"value":14,"label":15},"Upper tool","Punch position",{"value":17,"label":18},"Documented limits","Machine\u002Ftool provider",[20,24,27,50,53,61,64,66,72,75,77,84,87,94,103,106,126,128,130,133,135],{"type":21,"text":22,"id":23},"h2","What the punch is","section-4",{"type":25,"text":26},"p","The punch is the upper tool on a press brake. Relative movement of the upper and lower tools presses the sheet into the lower die. The tip contacts the inside of the bend, the body provides working height, and the neck or offset provides room for already formed flanges.",{"type":28,"head":29,"rows":33},"table",[30,31,32],"Problem","Next check","Bring these records",[34,38,42,46],[35,36,37],"Later bend obstructed","Check orientation and section at every bend, then the candidate profile’s actual load limits and loading conditions. Clearance alone does not establish selection.","Bend sequence, formed flanges and candidate punch load-limit documents",[39,40,41],"Tip or visible face unsuitable","Check angle, tip radius and condition","Tool drawing and part surface requirements",[43,44,45],"Clamping interface unknown","Check the actual interface documentation","Punch shank, holder, adaptor and machine identification",[47,48,49],"Load unknown","Use the worksheet below; verify actual load capacity using documents supplied by the machine\u002Ftool providers. This page does not supply that data.","Material, active V opening, actual engaged length and supplied load-limit documents for the assembly",{"type":21,"text":51,"id":52},"Selection guidance and failure modes","section-9",{"type":54,"items":55},"ul",[56,57,58,59,60],"Match the punch angle and tip to the required bend and to the visible face; a tip that is convenient for the die can leave an unacceptable mark.","If the first bend fits but a return flange enters the straight punch body’s space on the second bend, review sequence and part orientation before comparing clearance profiles. A taller or gooseneck punch is not automatically suitable.","Check rated load per metre using the actual engaged length, not nominal tool length or material thickness alone.","A punch chosen only by tonnage can be too short for the part, and a punch chosen only by height can be overloaded at the tip.","A worn or damaged tip transfers a mark to every part, so tip condition belongs in the setup check.",{"type":21,"text":62,"id":63},"How it works","section-6",{"type":25,"text":65},"Relative movement of the upper and lower tools transfers bending force into the sheet. In air bending, the inside radius depends mainly on the V opening, while the tip can mark the inside surface and tool geometry constrains flange clearance. The tip radius is not the unloaded inside radius. Compare required line load with applicable tool limits and total force separately with machine capacity.",{"type":54,"items":67},[68,69,70,71],"Tip form: a sharp tip concentrates force and can mark the inside face; a rounded tip spreads the load but does not by itself set the air-bend radius.","Working height: enough height is needed to clear the part and any flange already formed.","Neck and offset: the shape of the punch body sets the clearance for return flanges.","Rated load: every punch has a load limit per metre, and compare calculated and rated loads in the same units, then check local and assembly limits.",{"type":21,"text":73,"id":74},"Gooseneck punches: return-flange clearance and load limits","section-11",{"type":25,"text":76},"A gooseneck profile provides directional clearance for a return flange. Check the part, tool, holder and machine geometry together through the bend sequence. [A2] Neither appearance nor similar dimensions establish a rated load or interface compatibility.",{"type":54,"items":78},[79,80,81,82,83],"Clearance is directional: check part orientation and bend sequence against the punch profile.","If a return flange or box upstand obstructs a straight punch, review the sequence before assessing a gooseneck candidate.","Clearance alone is insufficient: check the candidate’s actual load limits and loading conditions. Do not transfer a straight-punch rating to a gooseneck.","Compare the required force per metre for the actual engaged length with the candidate gooseneck’s documented limit, including local and assembly restrictions.","Check the complete swept clearance using the manufacturer-approved safe setup or simulation method before any trial stroke.",{"type":21,"text":85,"id":86},"Setup and inspection notes","section-14",{"type":54,"items":88},[89,90,91,92,93],"Use the actual tooling and clamping-system documents to check the shank interface, seating and location requirements, clamping and retention mechanisms, adaptors and permitted combinations. Similar appearance or insertion is not compatibility evidence. If interface documents are missing, leave compatibility unresolved; do not use a trial stroke to establish it.","Confirm the punch is seated and clamped correctly in the holder before the first stroke.","Check punch-to-die alignment across the full working length.","Inspect the tip for wear, chipping or built-up material before a batch.","Only after interface compatibility, clearance and applicable load limits have been verified under the approved procedure, run an authorized trial part and inspect the inside surface for marks.",{"type":25,"text":95},[96,97,102],"For unresolved machine opening, stroke or interface configuration, use the ",{"key":98,"href":99,"role":100,"label":101},"punch-machine-selection","\u002Fguides\u002Fhow-to-choose-a-press-brake\u002F","supplement","press brake selection guide",".",{"type":21,"text":104,"id":105},"Load and clearance release worksheet","section-1",{"type":28,"head":107,"rows":110},[108,109],"Check","Record and compare",[111,114,117,120,123],[112,113],"Units","Estimated total F in kN; engaged bend length L in m; distributed estimate q = F\u002FL in kN\u002Fm, L > 0",[115,116],"Actual assembly","Punch, active die opening, holder, adaptor and machine IDs; each applicable rating with units",[118,119],"Short or interrupted loading","Use manufacturer limits for short segments, cut-outs, eccentric loads and minimum engagement; do not assume uniform loading",[121,122],"Clearance","Check full bend sequence against part, tool, clamp and machine geometry using the manufacturer-approved safe method",[124,125],"Release","Keep the estimate, rating documents and first-part unloaded angle\u002Fradius; do not infer safety from machine total force alone",{"type":25,"text":127},"For a unit-conversion example, assume 100 kN is distributed uniformly over 0.50 m: the average line load is 100\u002F0.50 = 200 kN\u002Fm. Compare this with the applicable tool and assembly ratings, including local loading conditions. Use the actual engaged length for each job. [A1]",{"type":25,"text":129},"Machine force and tool line-load ratings use different units: convert kN to kN\u002Fm using contact length before making the comparison.",{"type":21,"text":131,"id":132},"Work the numbers","section-16",{"type":25,"text":134},"Use the press brake tonnage calculator to check total force F; divide F by actual engaged length L in metres for line load F\u002FL, and the V-die opening calculator when the punch and die have to be matched to a required radius and flange. Record the punch and die combination with the program so a later change can be traced. Calculators provide estimates, not confirmation of interface compatibility, load limits or measured performance.",{"type":136,"items":137},"cards",[138,146],{"title":139,"text":140,"href":141,"image":142,"alt":143,"width":144,"height":145},"Press brake tonnage calculator","Check the force needed for the material, thickness, length and V-die opening.","\u002Fcalculators\u002Fpress-brake-tonnage\u002F","\u002Fimages\u002Fknowledge-card.svg","Open the press brake tonnage calculator",1200,900,{"title":147,"text":148,"href":149,"image":142,"alt":150,"width":144,"height":145},"V-die opening guide","How the lower die opening influences radius, minimum flange and tonnage.","\u002Fknowledge\u002Ftooling\u002Fv-die\u002F","Read the V-die opening guide",{"title":152,"items":153},"Sources and scope",[154,159],{"id":155,"title":156,"url":157,"note":158},"A1","WILA — Tooling catalogue","https:\u002F\u002Fcatalog.wilatooling.com\u002FWILA-Catalog-USA\u002F","Manufacturer catalogue states maximum loads per unit length for named tooling\u002Fholders. No rating is transferred to an unidentified RAGOS tool; use the actual assembly documentation.",{"id":160,"title":161,"url":162,"note":163},"A2","WILA — Box bending","https:\u002F\u002Fwww.wilatooling.com\u002Fapplications\u002Fbox-bending\u002F","Directional return-flange clearance and joint checks of part, tool, holder and machine geometry only; no product dimensions, performance or RAGOS compatibility inferred.",[165,168,171,174],{"label":166,"path":167},"Press brake machines","\u002Fpress-brake\u002F",{"label":169,"path":170},"Tooling comparison","\u002Fknowledge\u002Ftooling\u002F",{"label":172,"path":173},"V-die opening calculator","\u002Fcalculators\u002Fv-die-opening\u002F",{"label":175,"path":176},"Press brake bending","\u002Fknowledge\u002Fprocesses\u002Fbending\u002F",{"heading":178,"text":179,"button":180},"Equipment and technical enquiries","Contact JS Ragos about the equipment or technical topics covered here.","Contact us",1794847192035]